Low Cost Singleshot & MultiShot Inclinometer

Low Cost Singleshot & MultiShot Inclinometer

ER-SMLT-01 (0~180°±0.2°)
1. Inclination: ±0.2°;
2. Azimuth: ±1.0°;
3. Tool face: ±0.5°.

Low Cost Singleshot & MultiShot Inclinometer

Low Cost Singleshot & MultiShot Inclinometer

Get Price Now



    Share to:

    Introduction

    ER-SMLT-01 Low Cost Singleshot & MultiShot Inclinometer

    Introduction

    ER-SMLT-01 Low Cost Singleshot & MultiShot Inclinometer is used for measuring the inclination angle, azimuth angle, orientation of magnetic operating face and orientation of high side operating face of at the end of the drilling hole or a specific position while drilling.

    It is widely applied for survey of well-hole drilling in the fields of petroleum, coal mine and irrigation establishment.

    Features

    1. For various operational purposes:

    Satisfying various survey purposes either for suspending measurement or self-floating measurement once equipped with different external protectors

    2. High precision and reliability:

    As the key part of inclinometer, acceleration sensor with a shockproof accelerometer have characteristics of high linearity, little temperature drifting and good recurrence, etc.

    3. Power-off protection:

    Power failure caused by shakes or pressures would not result in operational disruption or data loss.

    4. Dynamic performance:

    Excellent data collecting and processing in either dynamic or static performance.

    5. Shock and impact-resistance:

    External multi-vibrate-resist buffer, both radial and axial.

    6. Low temperature environment suitable:

    Normal performance at -40℃

    7. Deep-well measuring:

    Equipped with heat insulation protector, normal working at 250℃, under 125 MPa

    Specifications

    Diameter: Ф32 and Ф27

    Inclination: 0~180°±0.2°

    Azimuth: 0~360° ±1.0° (Well inclination ≥6°)

    High side operating face: 0~360°±0.5° (Well inclination ≥6°)

    Magnetic operating face: 0~360°±1.0° (Well inclination ≤8°)

    Delay range: 1~99min, minimum 1min

    Interval range: 1~99sec, minimum1sec (only for multi-shot)

    Max. sampling: 3600 points (only for multi-shot)

    Continuous working time: min 20 hrs (only for multi-shot)

    Shock resistance: ≤4.5 g, 10~100Hz

    Impact resistance: ≤2000 g, 0.5ms

    Voltage: DC6V~DC8V

    Current: under DC5V, stand-by condition ≤30 mA, data-collecting ≤150 mA

    Temperature: -40℃~125℃ (max. 250℃ with heat insulation protector)

    Rechargeable battery

    For single shot

    Voltage output: DC 7.2V.

    Electricity output: ≥500mAh

    Working Temperature: -40~125℃

    Charge or discharge times: ≥800 times

    Charging time: 2~4H

    Discharging time: ≥30min

    For multi shots

    Voltage output: DC6V

    Electricity output: ≥2000mAh

    Working temperature: -40~125℃

    Charge or discharge times: ≥800 times

    Charging time: 16~17H

    Discharging time: ≥12h


    Application Techniques

    1.Three Signal Transmission Methods of MWD Inclinometer While Drilling

    2.Do you Know the Working Principle of Inclinometer ?

    3.What is an Inclinometer While Drilling?

    4.What Is The Initial Alignment Of The Inclinometer?

    5.What do I need to pay attention to when using an inclinometer?

    6.Selection And Application Of Fiber Optic Gyroscope Inclinometer

    More Products


    Gyro-While-Drilling-FOG-INS-1
    Gyro While Drilling FOG INS

    Small Diameter Measurement While Drilling
    Small Diameter Measurement While Drilling

    High-temperature North Seeking MEMS Gyro For Gyro Tools(125°C)
    High-temperature North Seeking MEMS Gyro(125°C)

    Low Cost Measurement While Drilling
    Low Cost Measurement While Drilling

    FOG Continuous Gyro Tools
    FOG Continuous Gyro Tools

    High Performance North Seeking MEMS Gyroscope
    High Performance North Seeking MEMS Gyroscope
    Ask for a Quote



      Menu